• Ultra-Low Profile: <1.0mm thickness for zero-friction movement and discrete corporate and athletic wear.
• Nano-structured Mat: Electrospun, biodegradable nanofibrous matrix engineered for maximum skin integration.
• Medical-Grade Adhesive: Non-toxic, high-adhesion polymer designed by 3M to survive heavy training sweat and high-stress workdays.
• Delivery State: Plant-based compounds are encapsulated in an amorphous, non-crystalline state for on-demand release upon hydro-activation. Protected from oxidation to preserve the activity of plant-based ingredients

Unlike traditional patches that require daily reapplication, this electrospun nanofibre patch delivers steady plant-based actives for 72 continuous hours. Eliminate the daily cognitive load of tracking pills and lock in an uninterrupted wear cycle.

• Long-Wearing Application: 72 hours of continuous topical comfort wear.
• Near-Total Transfer: Zero wasted bandwidth. Traditional patches leave up to 95% of the actives trapped in the patch when discarded. The SkinSync™ nanofibre matrix fully dissolves, leaving zero active residue upon removal (when applied correctly for the full 72-hour cycle).

Formulated for 24/7 application — pre/post-training or pre/post-boardroom. A single patch enables a seamless transition between high-output execution, deep sleep, and your recovery window for three full days.

• Optimal Surface Activation: Apply on any relatively flat muscular zone to ensure full activation.
• Target Zones: Upper arm, lower arm, thigh, calf, rear deltoid, lower or upper back for best performance.

Yes. You can safely wear multiple SkinSync™ Patches at once and combine them with your existing training stack.

The patch is a moisture-activated topical delivery system — 3 phases:

• Phase 1 — Cleanse the Target Zone: Clear the selected placement zone of any heavy lotions or oils. A clean surface ensures uncompromised adhesive integration around the perimeter.
• Phase 2 — Hydrate for Ignition: Lightly moisturise the exact skin surface where the centre of the patch will rest. This is the critical step. SkinSync's electrospun nanofibre matrix is hydro-activated. Introducing surface moisture initiates a threedimensional dissolution process that unlocks the 72-hour long-wearing topical comfort cycle..
• Phase 3 — Apply: Peel away the protective layer, align the white active core directly over the moistened zone, and press firmly from the centre outwards for 20 seconds. Sealing the edges locks in the moisture, creating a closedloop delivery runway.

Immediate. Sensory feedback — a warming, cooling, or comforting sensation — begins within minutes of hydro-activation, confirming the dissolution process has begun. Because biological profiles vary, you retain complete control to remove the patch at any time. The continuous long-wearing matrix is engineered precisely for a 72-hour runway.

We recommend maintaining the full application window as part of your core weekly performance ritual.

The patch is shower-resistant — not shower-proof for extended periods. Minimal water exposure during wear will extend adhesion and maximise the full 72-hour delivery cycle. Keep patch exposure to water to a minimum and pat dry after showering.

Because the adhesive is engineered for a 3-day grip, pulling it off dry can compromise the skin surface. Use the 'Low and Slow' extraction protocol:

1. Saturate: Apply a wet compress or run under warm water for 60 seconds to deactivate the bond.
2. Extract: Grip one edge and peel the patch back flat against itself — parallel to the skin, not straight up — following the direction of hair growth.
3. Reset: Any residual border adhesive rinses away cleanly with warm water and standard soap, leaving zero sticky residue on your skin.

Yes. SkinSync™ uses a hydrophobic adhesive barrier specifically built to withstand heavy perspiration, high-humidity environments, and daily showering without losing grip.

The patch is designed to withstand daily showering. Prolonged direct water over the whole patch — such as standing under a shower stream for an extended period — will accelerate the dissolution process. For best results, keep shower time brief and water over the patch to a minimum. Simply pat dry rather than rubbing the patch after showering. Think of it like your performance wearables — precision-engineered to work hard, but worth a little care. Keep water exposure minimal and the patch will deliver for the full 72-hour cycle.

Yes. The 72-hour long-wearing matrix is built precisely for multi-day training blocks. There is zero need to remove or replace the patch between a morning long run, a high-stakes corporate meeting, an evening lift, or deep recovery sleep. The system maintains total structural integrity through intense friction and sweat cycles for up to 3 days.

No. You control the timeline. While the system is optimised for a 72-hour runway to extract maximum value, you can remove the patch at the 48-hour mark or earlier based on your personal preference. Because the long-wearing matrix maintains a steady, continuous topical comfort from the moment of hydro-activation, your skin receives continuous topical comfort for the entirety of the time it is applied.

No. Unlike traditional bulky gel patches or thick hydrocolloids, SkinSync™ nanofibre mats feature an ultra-low profile under 1.0mm. It lays completely flat against the skin surface — entirely undetectable under slimfit dress shirts, corporate suits, or high-performance athletic compression gear.

No. While the matrix carries highly concentrated natural botanical actives, our electrospinning technology locks the molecular compounds securely within the nanofibre matrix, preventing ambient evaporation. There are no lingering menthol, eucalyptus, or herbal scents to compromise your professional environment.